Rubbermount_EFI screaming eagle slip ons 80503-07
Hi everyone, I was recently looking on the harley Davidson web site USA, and on there they have a nice set of screaming eagle slip on silencers part no 80503-07 which require no mods to the air cleaner...
View ArticleClik here to view.
2300 twisty miles in 10 days on Ricor shocks
Well, I finally did it. I bit the bullet and purchased a set of Ricor shocks. My "S" shocks have been losing their tension and my ride has been getting progressively more wallowy (I'm sure I've made...
View ArticleIronhead Main shaft bearing race help
Ok so ask I was installing my tran I chipped the lip of the bearing race that sit in the case. If the thrust washer spins smooth is it safe to run it like that. Thanks
View ArticleTach help
New to the forum. Sorry if this is a stupid question but any help is greatly appreciated. I just got a 2009 1200 custom. I'm looking to relocate the speedo and do away with the tach. I'll probably do...
View Articleriders on the north shore?
hi/salut, since all of my riding buddys are in Montreal or the south shore I'm looking for some fellow sportster/hd/buell riders from the north shore/lower laurentians (around St-Eustache) I prefer...
View ArticleTurbo Ride Update
Well, finally installed the new clutch with stronger spring. The difference is dramatic to say the least. That slipping was allowing me to be lazy as acceleration was smoother and much slower, easy...
View ArticleIronhead Starter brunt?
Hey need help new here and first post! Hope for some help... Ok here goes, recently got a 76 Ironhead needed new wiring and few other things... So after getting the wiring job mocked up and making sure...
View ArticleIronhead Bottom end chatter
I have a constant rotational chatter sound kinda sounds like a bad bearing but it's not coming from the wheel or head both of which I teplaced in the past week .. I'm sorry guys 1983 xlh 1000 some of...
View ArticleClik here to view.
Hello from Texas
Hey everybody! I'm from Dallas, Tx. and I am riding a 2009 sportster 1200 Low. :) [IMG] Uploaded with ImageShack.us[/IMG]
View ArticleSuper Brace Ordered
A few weeks ago there was a thread on a Group Buy through Super Brace, I ordered one, but have not yet received it for my '02 XL1200C, I checked my bank account and the $$$ has been taken out of my...
View ArticleClik here to view.
Pulled the Trigger
It was sad to let my Sportster go but last night I made the decision to get a larger bike for a more comfortable commute and so the wife and I could spend more quality time on the bike. I hurt my back...
View ArticleIronhead pushrod ??
Ok i have adjusted my pushrods a couple of times, and I have not asked this question yet, but its been bothering me, so when I adjust the rods they are all fine, but the second to the back (I don't...
View ArticleIronhead Electronic Ignition for Electric AND Kick Start
Hi fellas, I'm looking at upgrading my 75 to electronic ignition. I'd really like to use the popular Ultima 53-660 programmable kit that's been discussed here, but it seems to present a problem. My...
View ArticleAbout to get Air Hammered!
Just ordered my Air Hammer from Hammer Perf! Just waiting on it and my Bassani Pro Streets, both of which will be here next week. Finally going to have a Harley that sounds like a Harley.:banana
View ArticleClik here to view.
No maps, no GPS, no schedule, just riding...
Well I needed to go on a short 2 day ride just to clear the cobwebs out and all. Now I am luckier than most since I live where a lot of people vacation, in the mountains of Wyoming about 80 miles from...
View ArticleClik here to view.
Caution- May cause an Erection! (New Air Cleaner)
Hey forum! I've been really busy the last couple weeks and I thought I would update you on my newly redesigned 7"x 3" round air cleaner. This thing is a CFM animal! I'm working out the details as to...
View Articlecustom tanks
ok so as i gear up to finally finish my nightster (ill post a build thread here as well as on chopcult) im tryin to figure out the little details and im stuck on the tank. so, im looking for pics of...
View ArticleThe dreadded exhaust flange nut
I was gotta remove my exhaust so I could do some work around the cam chest.....when the darn nuts on the front head exhaust flange wouldn't come off...I could just feel it ,it was going to bust the...
View ArticlePowdercoat under fender?
Hey all, just started stripping my bike today for the work I'm about to get done, had a thought pop into my head... makes sense to me to get the underside of the fender powdercoated along with all the...
View Article