Ironhead 73 xlch kickstarter shaft
I need to redo my kicker shaft end play I have shims but the kicker gear stop pin that is peened into the case needs tightened I have a new one but the manual isn't clear on the replacement process....
View ArticleDeutsch elimination and BUS ERR
What a nightmare. Okay, I removed all of the deutsch connectors and hard-wired them. I haven't had any front blinkers for a while, so I cut off the remaining connector that was just taking up space. I...
View ArticleRubbermount_EVO how far off center is too far for drive belt on rear sprocket ?
I didn't look at the belt on the rear sprocket until I got home after having the dealer put a new rear tire on the the 2004 sporty :frownthre if the belt sets against one side of the sprocket(outer...
View ArticleBack again
Well, Back many years ago, I was a member on here. I had a 91 XL1200 customized with an AME chopper kit, softail style rear fender, stretched tank, custom front fender, forward controls, and upswept...
View ArticleClik here to view.
Hello from Missouri!
What's up everyone? I've been creepin' around this site soaking up as much information as possible and I figured I should properly introduce myself. I'm not new to motorcycles or to Harley Davidson. I...
View ArticleIronhead starter confusion. Help please
Very confused and out of ideas. Went to start the bike and nothing. I have lights but nothing when i hit the button, no dimming of lights no wharrr or clank of the starter nothing. Figure maybe the...
View ArticleWhere is speedo sensor?
Iv been looking all over the bottom left of the right side of the frame because I wanna try cleaning it off because my speedo is jumping all over. anyone wanna be specific? maybe even a pic?? my bike...
View ArticleDifferent seats and bars for 2013 48 ?
Hi guys, I'm I'm new to Harleys, and this forum. I have just bought a 2013 48 and want to change the riding position and comfort factor. The original seat.. and my anatomy, are incompatible. :D I want...
View ArticleIronhead Ironhead's runnin bitchin somethin's wrong. HELP!
no problems what so ever. the ironhead runs Fan-Tastic. someone PLEASE tell me what i'm doing wrong?! H-E-L-P. ✠ laugh:laugh:laugh:laugh:laugh:laugh:laugh:laugh:la ugh:laugh:laugh ☠☠☠☠☠☠☠☠☠☠☠☠☠☠☠☠☠☠
View ArticleHonda CM400T Starting Problem
I bought a 1978 CM400T a bit back and after I tore it completely down and rebuilt it cafe style it ran great (after carb cleaning of course). I rode it around and let the GF chase me around on it...
View ArticleHello from Ottawa Illinois
I have been looking over the forum since late May for ideas on making the 2009 Nightster ready for daily commute of 84 miles. In addition to a camping road trip from Illinois to Ft Carson Colorado /...
View ArticleIronhead Improvements
Well a couple of weeks ago,I was coming home from a ride and began losing my lights intermittenly,so I figured it was time to dig into my electrics,I Was ,of course "putting it off" til I had time!(I...
View ArticleIronhead AMF original key switch repairable?
I got an original ignition from the amf years, big " AMF HARLEY DAVIDSON" stamped on the key and id like to use it. when I hooked it up, all 3 positions work, but it will not stay in the on position....
View ArticleT-Town drags in Tulsa
Ok the time is almost here. Oct 27th @10 am Tulsa raceway park. T-Town drags is an all harley drag race with classes for all models. Come out and have a good time. There will be dyno races, real races,...
View ArticleNight stalled and turned off
Hey folks, second post here, so I may be misplacing this thread but relevant. This may be nothing, or something major.... I was riding back to work on my nighty and I noticed that it did not ride as...
View ArticleOOPss
Well folks I had buckhorn bars on my 98 and just wanted to change them for a simple 10" ape well the ape hangers came in and after putting them on the bike the brake line is about 2-3 inches short...I...
View ArticleClik here to view.
Ironhead taps and dies, drill sizes
Dont remember if i posted this but with everyone asking about broken bolts I thought I`d post it. http://www.engineersedge.com/manufac...rill-chart.htm
View ArticleNew helmet?
I need a new helmet, I used to have a late 80s shoei. Then bought a cheaper one, the one I have now. It has lasted awhile, about 7 years. I'm looking for a light, top quality helmet that will last...
View Articlesporty shock swap
Hi all im new to the forum. Quick question ive got a 97 xl1200s I found some shocks that are from a 2010 xl1200. Can I bolt these up on my bike with little to no modification? Im looking to lower the...
View Article