Rubbermount_EFI Is it normal to be noisy after getting hot?
I've had a 2007 XL1200L for two months now. It had 2800 miles on it when I bought it and I've put another thousand on it since then. I love my bike. I try to ride every day and can't get enough of it....
View ArticleSeventy Two Speedo Bracket P/N
Anyone know what the part number is for the Speedometer Bracket for the Seventy Two? I'm looking to change out my riser and speedo bracket on my '05 Custom. The equivalent P/N for my year is 67053-95,...
View ArticleIronhead Tire size
Anyone know of a site that shows final tire deminsions mounted and aired...I need to send this info to Led Sled so they can make my rear fender and make it as tight as possible.
View ArticleClik here to view.
Clik here to view.
Ironhead Lets see where this leads me, '73 Sporty Project and Re Build
So I fell into a Sporty yesterday. Picked up a 73, that needs a new Jugs/Pistons/Rings and a good go through. Was told it's been punched out a few times, and the last on being the third, developed a...
View Articlemounting a yamaha pacifico fairing on my superlow
After getting backed into in traffic thus destroying my windshield, I bought a pacifico fairing to mount on it. I will post photos when I get to trying to mount it. Begin hate-fest now lol
View ArticleRear turn signal problems
New to this Forum, I have an '07 Nightster and am just completing chopping the rear. I thought this would be the easiest part of the job...boy was I wrong! The issue I am having is after wiring the new...
View ArticleClik here to view.
Ironhead valve seat problem-75 Xlh1000
So I was lapping the valves on my heads today and the first 3 I did looked fine. The 4th one not so on the good. I have a very thin contact on the exhaust valve. The valve itself cleaned up nice all...
View ArticleClik here to view.
Hammer Time
Yep I got Hammered! But seriously I just put the first 20miles on it since the heat cycles. I'm very happy with the whole process, Dan & Aaron over at Hammer are amazing, from the initial question...
View ArticleQuestion on changing primary oil
First time changing oil on a motorcycle, so I have a question.... For the primary oil change, can I just (after the oil has been drained) add the oil by the inspection cover by the chain instead of...
View ArticleIronhead Bare bones Project ebay
If your on a budget and want a CH, maybe this is a good start? http://www.ebay.com/itm/1973-Harley-...6c1bea&vxp=mtr
View ArticleClik here to view.
Question about inside of Primary Cover
I replaced the clutch pack and the spring today since I completed the Hammer Performance 1250 conversion and had a question about the inside of the primary cover. Should it look like this?...
View ArticleClik here to view.
Oil seepage - is this normal? (With pics)
Just noticed this today, and it has me a little concerned. My 07 XL1200R is slowly seeping oil from a few different places. Looks like the rear rocker box, and rear base gasket. Nothing major, and I...
View ArticleRubbermount_EFI Engine knock
So had my 883 upgraded to a hammer 1250. Just noticed an engine knock, not a ti tic tic but a thwak thwak thwak, mostly heard from the air intake. Am concerned that things are pretty bad, any ideas?
View ArticleUltra copper for cycle shack slip on?
I'm going to put on the cycle shack slip ons tomorrow, and was curious if I should use some ultra copper seal where the muffler meets the head pipe for a better seal. It was a suggestion someone made...
View ArticleRubbermount_EVO Cam Swap, Defenders, Carb, and intake mods done and suggestions
OK, I'm finally done with my mods and have taken several rides and I am VERY happy now!!, I also want to thank everyone who helped by offered help, advice and support, Thanks!!!! So, where do I start,...
View ArticleIronhead solo seat springs - which size to use
how do you know which size or type to use. say your six foot 2 inches tall and weigh 280 ish what type of spring would i need ?
View ArticleIronhead Valve/rocker arm making clicking noise
Just did my head gaskets on my 75 IH. Also replaced all 4 rocker arm spring. Going through my pushrod adjustment. And when my front exhaust valve closes I hear a loud clicking noise. The push rod is...
View ArticleMy pre-trip check
http://m.youtube.com/watch?feature=e...&v=vymd4tvpggk Did you catch who my companion is? Parrothead and Brad are excluded from guessing. LoL I leave Saturday morning.
View ArticleRubbermount_EVO Allen Wrench Socket Broke Off
So I'm there getting ready to change the oil in my primary I insert my allen wrench sock into the primary inspection plate bolt. Give it a turn and tip breaks off my socket. I tried to pick the broken...
View Article